| Fig. 1: Here is an example of a simple automotive circuit.
When the switch is closed, power from the positive battery terminal flows
through the fuse, the switch and then the load (light bulb). The light
illuminates and the circuit is completed through the return conductor
and the vehicle ground. If the light did not work, the tests could be
made with a voltmeter or test light at the battery, fuse, switch or bulb
socket
|
Perhaps the easiest way to visualize a circuit is to think of connecting a light bulb (with two wires attached to it) to the battery. If one of the two wires was attached to the negative post (–) of the battery and the other wire to the positive post (+), the circuit would be complete and the light bulb would illuminate. Electricity could follow a path from the battery to the bulb and back to the battery. It's not hard to see that with longer wires on our light bulb, it could be mounted anywhere on the vehicle. Further, one wire could be fitted with a switch so that the light could be turned on and off. Various other items could be added to our primitive circuit to make the light flash, become brighter or dimmer under certain conditions, or advise the user that it's burned out.
Some automotive components are grounded through their mounting points. The electrical current runs through the chassis of the vehicle and returns to the battery through the ground (–) cable; if you look, you'll see that the battery ground cable connects between the battery and the body of the vehicle.
Every complete circuit must include a ``load'' (something to use the electricity coming from the source). If you were to connect a wire between the two terminals of the battery (DON'T do this, but take our word for it) without the light bulb, the battery would attempt to deliver its entire power supply from one pole to another almost instantly. This is a short circuit. The electricity is taking a short cut to get to ground and is not being used by any load in the circuit. This sudden and uncontrolled electrical flow can cause great damage to other components in the circuit and can develop a tremendous amount of heat. A short in an automotive wiring harness can develop sufficient heat to melt the insulation on all the surrounding wires and reduce a multiple wire cable to one sad lump of plastic and copper. Two common causes of shorts are broken insulation (thereby exposing the wire to contact with surrounding metal surfaces or other wires) or a failed switch (the pins inside the switch come out of place and touch each other).
Some electrical components which require a large amount of current to operate also have a relay in their circuit. Since these circuits carry a large amount of current (amperage or amps), the thickness of the wire in the circuit (wire gauge) is also greater. If this large wire were connected from the load to the control switch on the dash, the switch would have to carry the high amperage load and the dash would be twice as large to accommodate wiring harnesses as thick as your wrist. To prevent these problems, a relay is used. The large wires in the circuit are connected from the battery to one side of the relay and from the opposite side of the relay to the load. The relay is normally open, preventing current from passing through the circuit. An additional, smaller wire is connected from the relay to the control switch for the circuit. When the control switch is turned on, it grounds the smaller wire to the relay and completes its circuit. The main switch inside the relay closes, sending power to the component without routing the main power through the inside of the vehicle. Some common circuits which may use relays are the horn, headlights, starter and rear window defogger systems.
| Fig. 2: Damaged insulation can allow wires to break (causing
an open circuit) or touch (causing a short circuit)
|
It is possible for larger surges of current to pass through the electrical system of your vehicle. If this surge of current were to reach the load in the circuit, it could burn it out or severely damage it. To prevent this, fuses, circuit breakers and/or fusible links are connected into the supply wires of the electrical system. These items are nothing more than a built-in weak spot in the system. It's much easier to go to a known location (the fusebox) to see why a circuit is inoperative than to dissect 15 feet of wiring under the dashboard, looking for what happened.
When an electrical current of excessive power passes through the fuse, the fuse blows (the conductor melts) and breaks the circuit, preventing the passage of current and protecting the components.
A circuit breaker is basically a self repairing fuse. It will open the circuit in the same fashion as a fuse, but when either the short is removed or the surge subsides, the circuit breaker resets itself and does not need replacement.
A fuse link (fusible link or main link) is a wire that acts as a fuse. One of these is normally connected between the starter relay and the main wiring harness under the hood. Since the starter is usually the highest electrical draw on the vehicle, an internal short during starting could direct about 130 amps into the wrong places. Consider the damage potential of introducing this current into a system whose wiring is rated at 15 amps and you'll understand the need for protection. Since this link is very early in the electrical path, it's the first place to look if nothing on the vehicle works, but the battery seems to be charged and is properly connected.
